Matronics Email Lists Forum Index Matronics Email Lists
BBS Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Which leads for Alcor EGT?

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
bob.verwey(at)gmail.com
Guest





PostPosted: Mon Nov 26, 2012 4:49 am    Post subject: Which leads for Alcor EGT? Reply with quote

Gents,I have a mint condition Elcor Ekonomix instrument plus Alcor 9411 probe p/n 86245. I do not have the leads to connect the two!
The setup tests fine when the probe is connected directly to the gauge, although I am not to sure about the calibration without the leads.


Can anyone tell me an easy way to set up 4 ft leads that would work please?
Bob Verwey

[quote][b]


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
nuckolls.bob(at)aeroelect
Guest





PostPosted: Mon Nov 26, 2012 11:08 am    Post subject: Which leads for Alcor EGT? Reply with quote

At 06:48 AM 11/26/2012, you wrote:
Quote:
Gents,
I have a mint condition Elcor Ekonomix instrument plus Alcor 9411
probe p/n 86245. I do not have the leads to connect the two!

The setup tests fine when the probe is connected directly to the
gauge, although I am not to sure about the calibration without the leads.

Can anyone tell me an easy way to set up 4 ft leads that would work please?

According to this data sheet on Alcor's website

http://tinyurl.com/d4y7pdu

your probe is a type K device. You can fabricate
an type-K extension lead from the appropriate
wire but depending on your locale, it may
be hard to find. It should be crafted from stranded
type-K wire.

The factory offerings for extension cables
are ridiculously long for an SE aircraft

http://tinyurl.com/cj29577

You can order a small quanity of 20AWG stranded
K wire for $33 from Omega

http://tinyurl.com/2fpp8r

cut it to appropriate length and install PIDG
terminals to make the connections.
Bob . . .


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
bob.verwey(at)gmail.com
Guest





PostPosted: Tue Nov 27, 2012 12:15 am    Post subject: Which leads for Alcor EGT? Reply with quote

Much obliged to you, Sir!

Best...
Bob Verwey

On 26 November 2012 21:07, Robert L. Nuckolls, III <nuckolls.bob(at)aeroelectric.com (nuckolls.bob(at)aeroelectric.com)> wrote:
[quote]--> AeroElectric-List message posted by: "Robert L. Nuckolls, III" <nuckolls.bob(at)aeroelectric.com (nuckolls.bob(at)aeroelectric.com)>

At 06:48 AM 11/26/2012, you wrote:
Quote:
Gents,
I have a mint condition Elcor Ekonomix instrument plus Alcor 9411 probe p/n 86245. I do not have the leads to connect the two!

The setup tests fine when the probe is connected directly to the gauge, although I am not to sure about the calibration without the leads.

Can anyone tell me an easy way to set up 4 ft leads that would work please?

  According to this data sheet on Alcor's website

http://tinyurl.com/d4y7pdu

  your probe is a type K device. You can fabricate
  an type-K extension lead from the appropriate
  wire but depending on your locale, it may
  be hard to find. It should be crafted from stranded
  type-K wire.

  The factory offerings for extension cables
  are ridiculously long for an SE aircraft

http://tinyurl.com/cj29577

   You can order a small quanity of 20AWG stranded
   K wire for $33 from Omega

http://tinyurl.com/2fpp8r

   cut it to appropriate length and install PIDG
   terminals to make the connections.


  Bob . . .

====================================
om" target="_blank">www.aeroelectric.com
ooks.com" target="_blank">www.buildersbooks.com
et="_blank">www.homebuilthelp.com
="_blank">http://www.matronics.com/contribution
le, List Admin.
====================================
-List" target="_blank">http://www.matronics.com/Navigator?AeroElectric-List
====================================
http://forums.matronics.com
====================================



[b]


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group