Matronics Email Lists :: View topic - Z 16 Charging question

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Z 16 Charging question

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

wdaniell.longport(at)gmai
Guest

Posted: Sun Oct 17, 2021 3:56 pm Post subject: Z 16 Charging question

I have a Rotax 912 with a Z16 and Dynon Skyview

The ammeter sometimes ( defined as once every 25 flights)  goes off the chart to 60a. I get the red X over the instrument.  Then it comes back and goes down to normal and sits there at whatever loads I have on the system.  I have always assumed that this was a Dynon bug.

My Dynon has a shunt installed between the generator and the bus which measures the entire load normally rock steady at 7A or 8A when using the autopilot.  I also have an independant  hall effect sensor measuring amps on the fat wire to the battery.

Today I noticed on climb out that the hall effect sensor was showing battery charge oscillating from +1.7A to +2.5A - normally it is steady.  I switched off the alternator and the hall effect sensor showed steady -7A in agreement with the load shown on my dynon (7A).  (I turned around and landed immediately.)   Voltage is steady.

I checked the alternator as per https://pointsforpilots.blogspot.com/2012/12/testing-rotax-912914-generator-and.html.   All within limits.

So my next steps are to change the regulator, which involves taking out the crowbar because the BandC had one internally,  (I had already bought a BandC voltage regulator some time ago) and the battery which is pretty much due for a change.

Any other thoughts?

Thanks

William Daniell



LONGPORT



+1 786 878 0246

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

user9253

Joined: 28 Mar 2008
Posts: 1908
Location: Riley TWP Michigan

Posted: Mon Oct 18, 2021 3:32 am Post subject: Re: Z 16 Charging question

There is no way that a faulty regulator can make a Rotax dynamo put out 60 amps.

It is only capable of 20 amps or so.  There must be a bad connection somewhere.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Joe Gores

wdaniell.longport(at)gmai
Guest

Posted: Mon Oct 18, 2021 4:25 am Post subject: Z 16 Charging question

JoeThanks.  Yes ...the first time it happened it caused a bit of worry until i realised i had no smoke in the cockpit...and everything was working normally.   And once id calmed down i came to the same conclusion.  I have to fault find that.

But what do you think of the fluctuating battery charging level?   Is that normal?   Or might it be the instrument?

Will



William Daniell

+1 786 878 0246



On Mon, Oct 18, 2021, 07:36 user9253 <fransew(at)gmail.com (fransew(at)gmail.com)> wrote:



 	  Quote: 	
		  --> AeroElectric-List message posted by: "user9253" <fransew(at)gmail.com (fransew(at)gmail.com)>

 

 There is no way that a faulty regulator can make a Rotax dynamo put out 60 amps.

 It is only capable of 20 amps or so.  There must be a bad connection somewhere.

 

 --------

 Joe Gores

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=503553#503553

 

 

 

 

 

 

 ===========

  -

 Electric-List" rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/Navigator?AeroElectric-List

 ===========

  FORUMS -

 eferrer noreferrer" target="_blank">http://forums.matronics.com

 ===========

 WIKI -

 errer noreferrer" target="_blank">http://wiki.matronics.com

 ===========

 b Site -

           -Matt Dralle, List Admin.

 rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/contribution

 ===========

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

user9253

Joined: 28 Mar 2008
Posts: 1908
Location: Riley TWP Michigan

Posted: Mon Oct 18, 2021 7:45 am Post subject: Re: Z 16 Charging question

It is unlikely that the Skyview is at fault.  The vast majority of electrical problems are

caused by bad connections.  Take every related connection apart and reassemble.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Joe Gores

wdaniell.longport(at)gmai
Guest

Posted: Mon Oct 18, 2021 8:15 am Post subject: Z 16 Charging question

....sadly I think you're right.

William Daniell



LONGPORT



+1 786 878 0246

On Mon, Oct 18, 2021 at 11:50 AM user9253 <fransew(at)gmail.com (fransew(at)gmail.com)> wrote:



 	  Quote: 	
		  --> AeroElectric-List message posted by: "user9253" <fransew(at)gmail.com (fransew(at)gmail.com)>

 

 It is unlikely that the Skyview is at fault.  The vast majority of electrical problems are

 caused by bad connections.  Take every related connection apart and reassemble.

 

 --------

 Joe Gores

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=503558#503558

 

 

 

 

 

 

 ===========

  -

 Electric-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?AeroElectric-List

 ===========

  FORUMS -

 eferrer" target="_blank">http://forums.matronics.com

 ===========

 WIKI -

 errer" target="_blank">http://wiki.matronics.com

 ===========

 b Site -

           -Matt Dralle, List Admin.

 rel="noreferrer" target="_blank">http://www.matronics.com/contribution

 ===========

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

wdaniell.longport(at)gmai
Guest

Posted: Mon Nov 01, 2021 6:30 am Post subject: Z 16 Charging question

Update:

I installed a bandc AVC 1 voltage regulator.  This has integral overvoltage protection and an internal relay simplifying the installation.  I changed the voltage pick up location from the shunt to the bus.

Voltage, bus amps and battery charging amps are stable.

Interestingly the headset howl which I suppressed by turning down mic gain has also gone away and I can turn the mic gain up to 50%.



 



William Daniell



LONGPORT



+1 786 878 0246

On Sun, Oct 17, 2021 at 7:55 PM William Daniell <wdaniell.longport(at)gmail.com (wdaniell.longport(at)gmail.com)> wrote:



 	  Quote: 	
		  I have a Rotax 912 with a Z16 and Dynon Skyview

The ammeter sometimes ( defined as once every 25 flights)  goes off the chart to 60a. I get the red X over the instrument.  Then it comes back and goes down to normal and sits there at whatever loads I have on the system.  I have always assumed that this was a Dynon bug.

My Dynon has a shunt installed between the generator and the bus which measures the entire load normally rock steady at 7A or 8A when using the autopilot.  I also have an independant  hall effect sensor measuring amps on the fat wire to the battery.

Today I noticed on climb out that the hall effect sensor was showing battery charge oscillating from +1.7A to +2.5A - normally it is steady.  I switched off the alternator and the hall effect sensor showed steady -7A in agreement with the load shown on my dynon (7A).  (I turned around and landed immediately.)   Voltage is steady.

I checked the alternator as per https://pointsforpilots.blogspot.com/2012/12/testing-rotax-912914-generator-and.html.   All within limits.

So my next steps are to change the regulator, which involves taking out the crowbar because the BandC had one internally,  (I had already bought a BandC voltage regulator some time ago) and the battery which is pretty much due for a change.

Any other thoughts?

Thanks

William Daniell



LONGPORT



+1 786 878 0246

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum