Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Insulator in durable gas tight compression

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
jan_de_jong(at)casema.nl
Guest





PostPosted: Mon Mar 04, 2019 12:29 am    Post subject: Insulator in durable gas tight compression Reply with quote

I have a simple question.
Is there any example in acceptable practices where an insulating layer
(some laminate?) is part of the stack of metal layers that is compressed
to ensure a durable gas tight low resistance electrical connection
between the metal layers?
If there is such that would be great. If such can be categorically
denied that would be great too.
Thanks.
Jan de Jong


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
user9253



Joined: 28 Mar 2008
Posts: 1900
Location: Riley TWP Michigan

PostPosted: Mon Mar 04, 2019 7:33 am    Post subject: Re: Insulator in durable gas tight compression Reply with quote

Some switches are made with a layer of plastic included in the compressed electrical connection.
They are prone to fail. How about mica?


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Joe Gores
Back to top
View user's profile Send private message
jan_de_jong(at)casema.nl
Guest





PostPosted: Mon Mar 04, 2019 12:36 pm    Post subject: Insulator in durable gas tight compression Reply with quote

Bob, Joe, Dick, thank you.
This is exactly what I meant - is it possible to combine mechanical
connection, isolated, with electrical connection, gas tight as required,
by compressing the whole lot. It appears not - the functions have to be
separated because the isolating panel material is likely to relax too
much. In any case it looks like it is not in the accepted toolbox.
Sorry I caused confusion.
Jan de Jong

On 3/4/2019 6:48 PM, Dick Tasker wrote:
Quote:

<dick(at)thetaskerfamily.com>

I believe you are asking is it okay to use some sort of laminate in
the stack-up of layers wherein the goal is to have something to mount
the connection to and insulate it from your airplane sheet metal and
that will not affect the "gas-tightness" of the connection.

If that is the question, I believe that the answer would be that there
are very few materials that would allow that.  Ceramic would work, but
that is hared to work with.  Any plastic type material probably is too
soft to not allow some relaxation over time of the joint.

The way to do what I think you want is to connect the bolt (or
whatever is part of the whole assembly) to the laminate with a nut and
then put the ring-lug (or whatever needs to be connected) onto the
bolt and then use another nut to make the connection gas tight. Or if
you are just using the laminate to hold the joint in place, place the
two lugs that need to be connected over the first nut and then use the
final to make it gas tight.

If I have misinterpreted your goal, then just ignore this comment.

Dick Tasker

Jan de Jong wrote:
>
> <jan_de_jong(at)casema.nl>
>
> I have a simple question.
> Is there any example in acceptable practices where an insulating
> layer (some laminate?) is part of the stack of metal layers that is
> compressed to ensure a durable gas tight low resistance electrical
> connection between the metal layers?
> If there is such that would be great. If such can be categorically
> denied that would be great too.
> Thanks.
> Jan de Jong
>



- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
jan_de_jong(at)casema.nl
Guest





PostPosted: Mon Mar 04, 2019 2:41 pm    Post subject: Insulator in durable gas tight compression Reply with quote

..
I was actually looking at very hard phenolic laminates and other hard
insulating materials and considering Belleville washers etc. at
McMaster. when I decided to pose my question as a sanity check. I do not
plan to experiment with my electrical connections.
Thanks,
Jan de Jong

On 3/4/2019 9:09 PM, Jan de Jong wrote:
Quote:

<jan_de_jong(at)casema.nl>

Bob, Joe, Dick, thank you.
This is exactly what I meant - is it possible to combine mechanical
connection, isolated, with electrical connection, gas tight as
required, by compressing the whole lot. It appears not - the functions
have to be separated because the isolating panel material is likely to
relax too much. In any case it looks like it is not in the accepted
toolbox.
Sorry I caused confusion.
Jan de Jong

On 3/4/2019 6:48 PM, Dick Tasker wrote:
>
> <dick(at)thetaskerfamily.com>
>
> I believe you are asking is it okay to use some sort of laminate in
> the stack-up of layers wherein the goal is to have something to mount
> the connection to and insulate it from your airplane sheet metal and
> that will not affect the "gas-tightness" of the connection.
>
> If that is the question, I believe that the answer would be that
> there are very few materials that would allow that.  Ceramic would
> work, but that is hared to work with.  Any plastic type material
> probably is too soft to not allow some relaxation over time of the
> joint.
>
> The way to do what I think you want is to connect the bolt (or
> whatever is part of the whole assembly) to the laminate with a nut
> and then put the ring-lug (or whatever needs to be connected) onto
> the bolt and then use another nut to make the connection gas tight.
> Or if you are just using the laminate to hold the joint in place,
> place the two lugs that need to be connected over the first nut and
> then use the final to make it gas tight.
>
> If I have misinterpreted your goal, then just ignore this comment.
>
> Dick Tasker
>
> Jan de Jong wrote:
>>
>> <jan_de_jong(at)casema.nl>
>>
>> I have a simple question.
>> Is there any example in acceptable practices where an insulating
>> layer (some laminate?) is part of the stack of metal layers that is
>> compressed to ensure a durable gas tight low resistance electrical
>> connection between the metal layers?
>> If there is such that would be great. If such can be categorically
>> denied that would be great too.
>> Thanks.
>> Jan de Jong
>>
>>
>>
>>
>>
>



- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
user9253



Joined: 28 Mar 2008
Posts: 1900
Location: Riley TWP Michigan

PostPosted: Mon Mar 04, 2019 2:57 pm    Post subject: Re: Insulator in durable gas tight compression Reply with quote

You can use two nuts on the bolt. The first nut holds the bolt in place on the
insulating material. The electrical ring terminals go on next followed by the
second nut. The two nuts compress the terminals together with no plastic in between.


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Joe Gores
Back to top
View user's profile Send private message
jan_de_jong(at)casema.nl
Guest





PostPosted: Mon Mar 04, 2019 3:42 pm    Post subject: Insulator in durable gas tight compression Reply with quote

Yes, separating the functions of locating and connection.
On 3/4/2019 11:57 PM, user9253 wrote:
Quote:


You can use two nuts on the bolt. The first nut holds the bolt in place on the
insulating material. The electrical ring terminals go on next followed by the
second nut. The two nuts compress the terminals together with no plastic in between.

--------
Joe Gores



- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group