Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Z19 first try and smoke/wire melted I did a mistake

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
nuckolls.bob(at)aeroelect
Guest





PostPosted: Sat Jun 16, 2018 3:12 pm    Post subject: Z19 first try and smoke/wire melted I did a mistake Reply with quote

Quote:

After that I investiguate quickly, and I find that I set the polarity on the wrong way. I set it in the good one.

Same result ! Wire coming red without no more insulation.

My first question is :

- my IFF/Radio/electronics ignitions and all the electronics parts are good to the bin ? (I have a Trig S mode... new electronics Ignitions) wire like the Z19 with a diode and without avionics switch like the Z19.

- Why I have in the bad polarity, but also in the good this wire that is comming hot and red ?

- I spoke about the electronics instruments, but the others wires could be damage as the wire spoke above ?

If you have some advise for the next step for me... I will appreciate [Rolling Eyes]

The first event probably shorted the diode across
the coil since it was in a FORWARD conduction mode.
Correcting the battery connection produced a similar
event because the diode was shorted.

Now, the good news. Since the diode fused and became
a 'wire burner', the contactor did not close. Similarly,
even with the proper battery connection, the shorted diode
kept the contactor from closing once again and only
the wiring was abused.

Replace the diode and any smoked wires. I'm hopeful that
the rest of your electrowhizzies are okay.



Bob . . .


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
Achille



Joined: 12 Jun 2017
Posts: 25
Location: Europe

PostPosted: Sat Jun 16, 2018 5:56 pm    Post subject: Re: Z19 first try and smoke/wire melted I did a mistake Reply with quote

Thank you bob for you reply. I hope to find just the diode end the wire U/S. Many thanks.

I have to check just the intégrity of contactor ground wire (master switch to the ground bus) easily accessible or I could have other wire damaged ?
Because all my wires are set in harness with sleeve.

About the possible damage, with luck just this wire and diode. But without
Alternator diode couldn't be damage at least ? and my ignitions and transpondeur ? (I checked on the user manuel they told that inversion of polarity damage it) But in the case of switch was in OFF on the transpondeur (for exemple) it can damage it ? (I ask the question because I was doing a quote of my error to be prepared in the event of I have to change part.. and total price become quickly crazy)


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group