Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

RE: Switch Washers/ugly hole

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
nuckollsr(at)cox.net
Guest





PostPosted: Tue Jan 03, 2006 5:51 am    Post subject: RE: Switch Washers/ugly hole Reply with quote


I always put anti-rotation washers on the back side. If your switch
panel includes an engraved overlay, then holes in the panel for the
tab holes can go all the way through . . . and tabs on washers trimmed
to insure they are flush or under-flush to the panel surface. If your
panel plans don't include an engraved overlay, then consider a rear shim of
sheet metal drilled for the anti-rotation tabs . . . the instrument
panel surface stays clean. Again, you may have to trim the anti-rotation tabs
a bit. I would avoid any kind of gluing operation for this installation
except maybe to hold the rear shim in place . . . a couple of spots of
Sho-Goo works good.
Bob . . .
At 11:28 AM 12/31/2005 -0500, you wrote:
Another way is to forget the washer and put a dab of RTV on the back/side of
the switch after it's tight.
Bruce
www.glasair.org

Quote:


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
dan(at)rvproject.com
Guest





PostPosted: Tue Jan 03, 2006 7:35 am    Post subject: RE: Switch Washers/ugly hole Reply with quote


Quote:
I always put anti-rotation washers on the back side. If your switch
panel includes an engraved overlay, then holes in the panel for the
tab holes can go all the way through . . . and tabs on washers trimmed
to insure they are flush or under-flush to the panel surface. If your
panel plans don't include an engraved overlay, then consider a rear shim
of
sheet metal drilled for the anti-rotation tabs . . . the instrument
panel surface stays clean. Again, you may have to trim the anti-rotation
tabs
a bit. I would avoid any kind of gluing operation for this installation
except maybe to hold the rear shim in place . . . a couple of spots of
Sho-Goo works good.
Bob . . .

You took the words out of my mouth. Except there's no need to hold the rear
shim in place if it serves more than one switch...it will be held and have
its own anti-rotation feature by virtue of being held by multiple switches.
See here:
http://rvproject.com/images/2003/20030615 switch backing plate.jpg
http://rvproject.com/images/2003/20030615 drilling switch holes.jpg
Yes, those photos show the plate on the front of the panel, but it installs
on the rear:
http://rvproject.com/images/2003/20030701 switch alignment plate.jpg
Sorry, those are crummy photos from my old camera, but you get the point.
) ( Dan
RV-7 N714D (756 hours since 3/27/04)
http://www.rvproject.com


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group