Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Mono Landing Gear Bungee

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
MJKTuck(at)cs.com
Guest
PostPosted: Tue Feb 02, 2021 6:03 pm    Post subject: Mono Landing Gear Bungee Reply with quote
Can anyone recall the diameter of the bungee used to assist gear
retraction on the mono? 3/8 inch maybe?

As I recall there is not much room for it to squeeze through as you go
around the frame. I think 1/2 inch would be too big - I'm pretty sure it
was bigger than 1/4 inch.

Also, what would be a good length to buy?

Regards,
Martin Tuck
Wichita, KS

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
ward.t(at)xtra.co.nz
Guest
PostPosted: Tue Feb 02, 2021 7:31 pm    Post subject: Mono Landing Gear Bungee Reply with quote
Hi Martin,
Just measured the old bungee I replaced.
Thickness 7mm = 5/16 just short 3/8. So 3/8”
Length 7m = 30ft
Hope that helps and I am correct.

Cheers,
Tim

Sent from my iPhone

Tim Ward
12 Waiwetu Street
Fendalton
CHRISTCHURCH 8052
Hom 03315166

Quote:
On 3/02/2021, at 15:11, Martin Tuck <MJKTuck(at)cs.com> wrote:



Can anyone recall the diameter of the bungee used to assist gear retraction on the mono? 3/8 inch maybe?

As I recall there is not much room for it to squeeze through as you go around the frame. I think 1/2 inch would be too big - I'm pretty sure it was bigger than 1/4 inch.

Also, what would be a good length to buy?

Regards,
Martin Tuck
Wichita, KS





- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
h&jeuropa



Joined: 07 Nov 2006
Posts: 634
PostPosted: Wed Feb 03, 2021 9:54 am    Post subject: Re: Mono Landing Gear Bungee Reply with quote
Martin,

The parts list that came with our kit shows 10mm x 6 meters for the bungee. We replaced ours a couple years ago with 20 ft of 10mm cord. We got it from Aircraft Spruce.

Jim & Heather

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
ward.t(at)xtra.co.nz
Guest
PostPosted: Wed Feb 03, 2021 10:44 am    Post subject: Mono Landing Gear Bungee Reply with quote
Martin,Jim is correct. They increased the diameter of the bungee in later Europa aircraft to 10mm. I remember now after 20 years.
Cheers,
Tim

Sent from my iPadTim Ward
12 Waiwetu Street,
Fendalton,
Christchurch, 8052
New Zealand.
ward.t(at)xtra.co.nz
021 0640221
Quote:
On 4/02/2021, at 7:02 AM, h&amp;jeuropa <butcher43(at)att.net> wrote:

--> Europa-List message posted by: "h&amp;jeuropa" <butcher43(at)att.net>

Martin,

The parts list that came with our kit shows 10mm x 6 meters for the bungee. We replaced ours a couple years ago with 20 ft of 10mm cord. We got it from Aircraft Spruce.

Jim & Heather


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=500550#500550

====================================================; - MATRONICS WEB FORUM====================================================; - NEW MATRONICS LIST WIKI -
_====================================================bsp; - List Contribution Web Site -
_ &n=======================================================




- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
rparigoris



Joined: 24 Nov 2009
Posts: 780
PostPosted: Wed Feb 03, 2021 11:26 am    Post subject: Re: Mono Landing Gear Bungee Reply with quote
Hi Martin
I installed bungee with one more loop compared to what manual shows. As per Nev, I left a tail on the bungee so if I want to tighten in future job will be easier.:
https://1drv.ms/u/s!Ah1S270Nwg9VylK4_khn10T8oiq_
Ron P.

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group