Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Y splitter

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
Argonaut36



Joined: 19 May 2019
Posts: 35

PostPosted: Sat Jul 06, 2019 7:09 pm    Post subject: Y splitter Reply with quote

I was wondering if the practice of twisting 2 wires together and crimping the resulting wire in a ring terminal can be considered acceptable, even for standard certificate airplanes, for making a Y splitter. If so, assuming that 2 wires to be twisted together are size 20#, should a red or blue ring terminal be used?
Thanks


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
View user's profile Send private message
alec(at)alecmyers.com
Guest





PostPosted: Sun Jul 07, 2019 3:38 am    Post subject: Y splitter Reply with quote

See:
http://www.aeroelectric.com/articles/multiplewires/multiplewires.html

See also:
https://www.te.com/content/dam/te-com/documents/industrial-automation-and-control/global/1773464-1_QRG_PIDG.pdf
FREQUENTLY ASKED QUESTIONS:
Can wires be combined in PIDG terminals & splices? Yes they can as long total CMA (Circular Mil Area) and insulation diameter fall within specification.

Also, per NASA-STD-8739.4A Section 19.9:

Crimping wires into contacts or crimp ferrules is a method for splicing wires together without soldering. When crimping multiple wires into a contact or ferrule, the total circular-mil-area (CMA) of all the wires must be calculated into an Equivalent Wire Size (EWS) in order to select the properly sized contact or ferrule.

19.9.1 The following requirements apply for crimped splices:

a. The tooling verification process and the completed termination shall comply with all the requirements of this document for a crimp termination except as specified herein for jiffy junction devices.

b. The contact/wires size and crimp tool setting combination shall be developed and verified using the same requirements as for any machined contact (see 12.3.5).

c. The crimp ferrule or contact shall be sized equivalently with the calculated Equivalent Wire Size (EWS) or the next larger EWS if the calculated value does not exactly match a single wire size.


Don’t twist the wires together, they should go into the barrel parallel. I believe when you double area of a wire, the AWG goes down by three. So 2 x 20 gauge wires would be 17 gauge.



On Jul 6, 2019, at 11:09 PM, Argonaut36 <fmlibrino(at)msn.com> wrote:



I was wondering if the practice of twisting 2 wires together and crimping the resulting wire in a ring terminal can be considered acceptable, even for standard certificate airplanes, for making a Y splitter. If so, assuming that 2 wires to be twisted together are size 20#, should a red or blue ring terminal be used?
Thanks


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=490084#490084


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
John M Tipton



Joined: 07 Aug 2018
Posts: 45
Location: Devon - England

PostPosted: Sun Jul 07, 2019 8:56 am    Post subject: Y splitter Reply with quote

And you still fuse for the the wire size ;(22awg - 3amp) although your using two 22awg wires that could be carrying 5/7amps

John

Sent from my iPad

----x--O--x----

Quote:
On 7 Jul 2019, at 12:37 pm, Alec Myers <alec(at)alecmyers.com> wrote:



See:
http://www.aeroelectric.com/articles/multiplewires/multiplewires.html



See also:
https://www.te.com/content/dam/te-com/documents/industrial-automation-and-control/global/1773464-1_QRG_PIDG.pdf
FREQUENTLY ASKED QUESTIONS:
Can wires be combined in PIDG terminals & splices? Yes they can as long total CMA (Circular Mil Area) and insulation diameter fall within specification.



Also, per NASA-STD-8739.4A Section 19.9:

Crimping wires into contacts or crimp ferrules is a method for splicing wires together without soldering. When crimping multiple wires into a contact or ferrule, the total circular-mil-area (CMA) of all the wires must be calculated into an Equivalent Wire Size (EWS) in order to select the properly sized contact or ferrule.

19.9.1 The following requirements apply for crimped splices:

a. The tooling verification process and the completed termination shall comply with all the requirements of this document for a crimp termination except as specified herein for jiffy junction devices.

b. The contact/wires size and crimp tool setting combination shall be developed and verified using the same requirements as for any machined contact (see 12.3.5).

c. The crimp ferrule or contact shall be sized equivalently with the calculated Equivalent Wire Size (EWS) or the next larger EWS if the calculated value does not exactly match a single wire size.




Don’t twist the wires together, they should go into the barrel parallel. I believe when you double area of a wire, the AWG goes down by three. So 2 x 20 gauge wires would be 17 gauge.







On Jul 6, 2019, at 11:09 PM, Argonaut36 <fmlibrino(at)msn.com> wrote:



I was wondering if the practice of twisting 2 wires together and crimping the resulting wire in a ring terminal can be considered acceptable, even for standard certificate airplanes, for making a Y splitter. If so, assuming that 2 wires to be twisted together are size 20#, should a red or blue ring terminal be used?
Thanks




Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=490084#490084
















- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
View user's profile Send private message
Argonaut36



Joined: 19 May 2019
Posts: 35

PostPosted: Sun Jul 07, 2019 5:15 pm    Post subject: Re: Y splitter Reply with quote

Thanks to All for the very good information provided!

- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group