Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Need to increase built-in Voltage Regulator limit by .5V

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
peter(at)schwenn.com
Guest





PostPosted: Thu May 03, 2018 10:05 am    Post subject: Need to increase built-in Voltage Regulator limit by .5V Reply with quote

AeroElectrocutors,

Rotax 912iS internal voltage regulator cutoff is 14.2.  Lithium-IRON (LiFePO4) needs 14.7 for full and timely charge.
I can't reasonably modify the internal regulator.
Is there a reasonable way to get 14.7V?
Thanks,
Peter Schwenn
P.S. Why would I want to use a lithium-iron battery? Don't Lithium-Ion batteries have a host of problems?
     In my experience they have just one: if fully discharged (approx: <10 V) they can be difficult and slow to recover. 
    They don't overheat or catch fire (as LiPo, LiCoO2,...can),  They contain nothing toxic or hazardous.  They needn't be charged slowly.  They can supply current rapidly.  They don't require a protective or heavy enclosure.
     All battery types differ in their requirements.  Lithium-Iron requires a special charger; for balancing cells, recovery from discharge, and NOT performing operations other types may require.

240-602-6931

6514 41st Av. U Park MD 20782
Eaa4 & Xenos N32XS (at) KCGS
N16XN under construction -
     Rivetless skins for Laminar Flow
http://www.schwenn.com


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
user9253



Joined: 28 Mar 2008
Posts: 1907
Location: Riley TWP Michigan

PostPosted: Thu May 03, 2018 11:00 am    Post subject: Re: Need to increase built-in Voltage Regulator limit by .5V Reply with quote

14.2 volts might be OK. Van's Aircraft put the new 912iS in their latest RV-12 along with a Lithium battery. Read what EarthX has to say:
https://earthxbatteries.com/engine-charging-systems-use-lithium-batteries


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Joe Gores
Back to top
View user's profile Send private message
peter(at)schwenn.com
Guest





PostPosted: Mon May 07, 2018 1:40 am    Post subject: Need to increase built-in Voltage Regulator limit by .5V Reply with quote

14.2 will charge a LiFePo battery but only about halfway and slowly. I use 3 Shorai LiFePo and an ultra light Micro (4ah) in a Ducati.  They all share the 4.7V requirement.  Since high rates of discharge and charge, and very low loss rate are properties of these cells, it doesn't make sense to use half the capacity - as it wouldn't for any battery.

[I appreciate the info for EarthLink aircraft LiFePo - they are the best, with a good controller built-in, and the fullest explanation of all details of charging.  Very expensive except that one is unlikely to destroy their batteries.]

240-602-6931


On May 3, 2018 04:43, "Peter Schwenn" <peter(at)schwenn.com (peter(at)schwenn.com)> wrote:
Quote:
AeroElectrocutors,

Rotax 912iS internal voltage regulator cutoff is 14.2.  Lithium-IRON (LiFePO4) needs 14.7 for full and timely charge.
I can't reasonably modify the internal regulator.
Is there a reasonable way to get 14.7V?
Thanks,
Peter Schwenn
P.S. Why would I want to use a lithium-iron battery? Don't Lithium-Ion batteries have a host of problems?
     In my experience they have just one: if fully discharged (approx: <10 V) they can be difficult and slow to recover. 
    They don't overheat or catch fire (as LiPo, LiCoO2,...can),  They contain nothing toxic or hazardous.  They needn't be charged slowly.  They can supply current rapidly.  They don't require a protective or heavy enclosure.
     All battery types differ in their requirements.  Lithium-Iron requires a special charger; for balancing cells, recovery from discharge, and NOT performing operations other types may require.

240-602-6931

6514 41st Av. U Park MD 20782
Eaa4 & Xenos N32XS (at) KCGS
N16XN under construction -
     Rivetless skins for Laminar Flow
http://www.schwenn.com


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group