Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

aileron push tubes

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV9-List
View previous topic :: View next topic  
Author Message
Peter Laurence



Joined: 10 Jan 2006
Posts: 50

PostPosted: Mon May 08, 2006 7:21 am    Post subject: aileron push tubes Reply with quote

Question for those of you that have installed the Stick to aileron bellcrank
push tubes.

Did you cut them as per Van's measurments before installing. If so, were the
measurments correct or were you "VANdalized"?

Peter Laurence
9A fuse


- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
View user's profile Send private message
Neilekins(at)aol.com
Guest





PostPosted: Mon May 08, 2006 7:35 am    Post subject: aileron push tubes Reply with quote

I cut them as per plans. I would add 1/4 inch to them. I had just enough
length for minimum amount threads to screw in..That was after I put the proper
angle of deflection. You can check out my web site. neilsplane.com Im
building a lancair esp now...Neil


- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
jc(at)INFONET.COM.BR
Guest





PostPosted: Mon May 08, 2006 8:15 am    Post subject: aileron push tubes Reply with quote

Ive cutted them by Vans manual with any problems. To centralize the sticks Ive got
some difficult. Some trials and errors using an plumb bob in both sticks. One hour job.
To install the washers between the sticks and bell crank it is etter to buy washer tool
at Avery.
PU-JCI
RV-9A
Flying 125 hs
JC - Aracaju - Brasil
websites.expercraft.com/jcmm


- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
Peter Laurence



Joined: 10 Jan 2006
Posts: 50

PostPosted: Mon May 08, 2006 9:31 am    Post subject: aileron push tubes Reply with quote

Thanks Neil

I'm from Tampsa. Where are you located/
Peter
(A fuse
---


- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV9-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group