Matronics Email Lists

Congrats on another milestone.............Bravo Zulu (well Done)

Frank @ 1L8 ...RV7A... N74BZ .... Flying

Thanks Bob for the info. My next trip to the airport will begin the process of trouble shooting as you suggest.

In regards to this part of the email I made a typo..

Now the questions. 1. W ...

I have wired my RV7A with the 13/8 revision L. I did modify it to include the LR3C Alternator controller in place of genric Ford Regulator and the AEC9005-101 Low Voltage Module. In looking at the 13/ ...

Hi Matt

Thanks for the ? and info. I have answered yoou in the body of your query.

> Date: Tue C 14 Jul 2009 17:56:59 -0600
Subject: RE: AeroElectric-List: Voltage problem
From: mpra ...

I am just about to put my RV7A in the air but....I have one minor problem to solve. The Dynon EMS D-120 is not indicating TRUE voltage output both with the engine in operation or when running on ...

Hi Matt

First C let me say your workmenship looks first rate. Secondly C I think you have run into a typical problem that most have faced at this point in the wing/tip build. Third C I think tha ...

Bob

I am one of your problem children.....not in my inbox or junk mail.......

fstringham@hotmail.com ( From: bob@rvbuildershotline.com
Date: Sun C 17 Aug 2008 06:40:22 -0700
To: rv-lis ...

While investigating my SD8/Battery problem it allowed me the opportunity to double check my wiring scheme per Z25 and the location of the components and wire runs. D- to near F....especially once the ...

Date: Thu C 3 Jul 2008 10:46:59 -0500> To: aeroelectric-list@matronics.com> From: nuckolls.bob@cox.net> Subject: Re: RE: AeroElectric-Battery/SD8 problem> >

Bob

Thanks for the ...

Hi to All

Last week I asked a question about my Odyessey 680 battery not being able to keep a charge. I am using the Z13/8 with SD8 self excitation. I thought I had checked all the suspects and ...

Hi all

Got a problem with my Odyssey 680 battery. It will not keep a charge. I am wired per Z13/8. Master and Endurance switches off.
At first I thought the trickle from the Dynon 100 was the ...

Jan

And I thought my 3 plus years was bad....you are an inspiration

Frank @ 1L8 ....RV7A ......final 992 details...........

From: owner-rv-list-server@matronics.com On Behalf Of ...

Dan

Congrats on the new found desire........Since Sept 4, 2004 I have been working off and on on an RV7A.....Like you family, work, $$$$$$$$$$$$$$$$$$$, life's responsibilities have turned a 18 ...

Joe

Check out Country State Name/E-mail Location Phone USA Florida Jan Bussell / janjoyce@strato.net 863-467-9354 USA Texas Dave Austin / flybaby60@aol.com Denton 214-236-7973 USA Alaba ...

Frank1

Hey whats up or is that down...good grief with your acro ability I never know what your attitude might be. Thanks for the response....now off to the garage to getter dun.................. ...

Ok so here is the set up...RV7A....SD-8 on the Vac pad....FWF Ground block just right of upper center on the firewall.
I have a clear run for the engine GND from the port side upper bolt on the SD- ...

went and measured my RV7A and it was 40 inches at the shoulder position.

Frank @ SGU RV7A

> To: rv-list@matronics.com
[quote] Subject: RE: RV-7 vs Mustang II
Date: Mon, 31 ...

Bob

To much Beer with Chili could make the mind a bit fuzzy I would suspect......I was given a wake up call at 2:00 AM sunday morning to bail my youngest child (26 going on 15) out of the count ...

Thanks Bob........it looks like a pretty easy wiring exchange from the old 13/8 to the now acceptable scheme......Thanks for all your efforts in behalf of we DIY guys and gals!!!!!!!

Frank @ SGU ...

Mike

Thanks for the info........

Frank @ SGU RV7A.................NDY................but real close!!!!!!!!!!!!!!!

Frank,

I wouldn't expect any answers back from Bob on th ...